Black Top Asphalt, LLC. Asphalt paving and sealcoating, Western North Carolina
Asphalt driveways that hold on a mountain grade.
New asphalt driveways, gravel-to-asphalt conversions and tar and chip lanes. Sealcoating, crack sealing and repair for the pavement you already have. Parking lots and private roads too, across five mountain counties.
- Free on-site estimate, price in writing
- Compacted stone base under every driveway
- Crowned and edged so mountain rain runs off, not in
- 5.0 stars on Google from 27 reviews
Pictured: one of our driveways, from our own site video.
What we pave
Driveways, lots and roads for mountain lots.
Each page below carries the real cost range, how the job is built and what changes the price on a slope. The prices shown come from those pages.
Asphalt driveways
Hot-mix asphalt on a compacted stone base, crowned and edged for mountain rain.
Typically $4 to $8 per square footAsphalt driveway paving
Gravel to asphalt
Your gravel becomes part of the base: regraded, compacted, then paved.
Typically $6 to $14 per square footGravel to asphalt conversions
Tar and chip
Asphalt binder with stone chips rolled in. The long-lane budget surface.
Typically $2.50 to $4.50 per square footTar and chip driveways
Sealcoating
Cracks filled first, then two coats of sealer to keep water and sun out.
Typically $0.18 to $0.35 per square footDriveway sealcoating
Driveway repair
Potholes, crumbling edges, alligator cracks and soft spots, patched or cut out.
Typically $250 to $900Asphalt driveway repair
Resurfacing and overlays
A new mat over pavement that is worn but not failed underneath.
Typically $2.50 to $6.00 per square footAsphalt resurfacing
Parking lots
Paved, drained and striped for real truck traffic, then sealcoated on a schedule.
Typically $3.50 to $7.00 per square footParking lot paving
Private roads
Subdivision streets and shared mountain roads, paved or chip sealed, ditches checked first.
Typically $3.50 to $7.50 per square footPrivate road paving
Steep driveways
Hot mix that holds on a real grade, with the water sent off the drive before it cuts a channel.
Typically $6,500 to $22,000Paving steep drivewaysWhat it costs
Real numbers before you call.
Written for Western North Carolina grades, clay and haul distances, not national averages. Every guide says what moves the price.
How much does an asphalt driveway cost?
Asphalt driveway cost in NC typically falls between $3,500 and $12,000 for a residential driveway in Buncombe County. A straightforward 12x50-foot install on gentle ground sits near the bottom; steep mountain lots with retaining walls, culverts and deep base correction push past $20,000.
Read the driveway cost guide $0.18 to $0.35 per square footDriveway Sealcoating Cost in NCDriveway sealcoating cost
Driveway sealcoating cost in NC typically runs $0.18 to $0.35 per square foot, so a standard two-car driveway in Buncombe County lands around $350 to $850. Long, steep, or narrow mountain driveways push higher because the crew loses time on access and the sealer has to travel further to reach the site.
Read the sealcoating cost guide $6 to $16 per square footCost to Pave a Gravel Driveway in NCCost to pave a gravel driveway
The cost to pave a gravel driveway in Buncombe County typically runs $6 to $16 per square foot for asphalt over a corrected base, with patch work starting near $1.50 and steep, drainage-heavy mountain drives pushing past $16. What separates those numbers is not the asphalt itself but what the gravel underneath tells you: cracks, potholes, soft shoulders and water decide whether you patch, overlay or tear out.
Read the gravel-to-asphalt guideOur work
Driveways, lots, roads, sealcoating and repair.
Job photos from Black Top Asphalt crews across Western North Carolina. Ask us to see a recent one near you in person.
How a driveway that lasts gets built
Four layers. The one you drive on is the last.
Mountain driveways fail from underneath: soft base, water with nowhere to go, asphalt laid too thin over both. So the base and the drainage are built first, and the hot mix is the finish.
Base
Cut to firm ground or regrade the gravel that is there, then compacted crushed stone, thick enough for the traffic the drive will carry.
Grade and water
Crown or pitch so rain runs off the edges, not down the middle. Ditches, culverts and edges sorted before any hot mix arrives.
Hot mix
Hot-mix asphalt laid hot and rolled tight while it is still hot, in the thickness the job calls for. Tar and chip where that is the better fit.
Edges, cure, seal
Edges tamped, the mat left to cure, and the first sealcoat scheduled once the asphalt is ready for it.
For how long after paving to sealcoat, most asphalt in Buncombe County needs 6 to 12 months of curing before sealcoating, and the cost typically runs $0.15–$0.30 per square foot. But what sits under the asphalt here — red clay, old gravel, or fill — determines how much crushed stone went down first, and that stone base is what controls whether your new pavement is ready on time or needs longer.
When to sealcoat, explainedStart with the problem
Tell us what the driveway is doing.
Most calls start with one of these. Each page says what the fix is, what it costs and when a new driveway is the honest answer.
Why is my asphalt driveway cracking?
Shrinkage, base movement or age, and which cracks can be sealed.
Potholes in the driveway.
Patch, overlay or replace, and how to tell which you need.
The edges are crumbling.
Why edges go first on a mountain drive, and the fixes that hold.
Water runs down my steep driveway.
Crown, swales, drains and where the water has to go instead.
Resurface or replace?
When an overlay is money well spent and when it is money on top of a failing base.
Something else on the pavement?
Send a few lines and a town. We will tell you if it is our kind of job.
Service area
Five mountain counties, from Waynesville to Brevard to Mars Hill.
We pave across Buncombe County and into Haywood, Henderson, Madison and Transylvania. Each town below has its own set of pages.
- Buncombe County
- Haywood County
- Henderson County
- Madison County
- Transylvania County
Asphalt driveway paving by town
Not on the list? If it is in one of the five counties, send the form. Hot mix travels; we plan the haul around the plant that is closest to you.
Questions we get on the first call
Straight answers, then a site visit.
How much does an asphalt driveway cost in Western North Carolina?
Asphalt driveway cost in NC typically falls between $3,500 and $12,000 for a residential driveway in Buncombe County. A straightforward 12x50-foot install on gentle ground sits near the bottom; steep mountain lots with retaining walls, culverts and deep base correction push past $20,000. The full cost guide breaks it down by length, thickness and what is under it.
Can you pave over my gravel driveway?
The cost to pave a gravel driveway in Buncombe County typically runs $6 to $16 per square foot for asphalt over a corrected base, with patch work starting near $1.50 and steep, drainage-heavy mountain drives pushing past $16. What separates those numbers is not the asphalt itself but what the gravel underneath tells you: cracks, potholes, soft shoulders and water decide whether you patch, overlay or tear out. See gravel to asphalt conversions.
What is tar and chip, and is it cheaper than asphalt?
Tar and chip driveways in Asheville, NC typically run $2.50–$4.50 per square foot installed , or roughly $3,500–$9,000 for a standard two-car driveway, with slope, base prep, and stone size driving the spread. On Buncombe County's graded lots, water — not traffic — decides how long the surface lasts, so crown, edges, and ditch placement matter as much as the binder. Tar and chip driveways.
How long after paving should I sealcoat?
For how long after paving to sealcoat, most asphalt in Buncombe County needs 6 to 12 months of curing before sealcoating, and the cost typically runs $0.15–$0.30 per square foot. But what sits under the asphalt here — red clay, old gravel, or fill — determines how much crushed stone went down first, and that stone base is what controls whether your new pavement is ready on time or needs longer. The timing, explained.
Do I need a permit to pave or add a driveway in North Carolina?
Expect $250-$1,500 in permit and engineering costs for a new driveway in Buncombe County, depending on NCDOT versus city jurisdiction and slope. NCDOT controls access on state-maintained roads, Asheville reviews driveways inside city limits, and steep mountain grades often trigger extra stormwater and sight-distance review. NC driveway permit rules.
What time of year can you pave in the mountains?
The best time of year to pave a driveway in North Carolina is generally late spring through early fall, when ground and air temps hold above roughly 50°F and rain is manageable. In Buncombe County, a residential asphalt driveway typically runs $2,400-$6,500 for a basic install, $5,000-$12,000 for longer or graded mountain drives, with overlays often $1,400-$4,200. The paving season, explained.
Free estimate
Ready when the driveway is.
Send the form or call (828) 606-0466. We come out, measure, check the base and the water, and put a real price in writing.